Uni Lifting System
Flat Steel Lifting
Coil&Ferrule Inserts
Lifting&Fixing Socket
Threaded Anchor
Channel Anchors
Forming Products
Edge Lift System
Wire Ropes
Rigging Hardware
Plastic Spacers
Workshop
Company News
Contact Us
Home
 
DR LIFTING SYSTEM FLAT STEEL LIFTING SYSTEM THREADED LIFTING SYSTEM A-ANCHORS™ WIRE ROPE LIFTING CHANNEL ANCHORS INSULATED PANEL CONNECTION SYSTEMS FIXING SOCKET PLASTIC SPACERS MAGNETS MAGNETIC SYSTEM FOR STEEL FORMWORK
UNI LIFTING SYSTEM
UNI LIFTING ANCHORS

1.Manufactured from a high quality steel.

2.Made from steel which remail good impact at low temperature .

3.Each anchor head is clearly marked and size

4.Anchors are tested at a specified sampling          rate(to failure) and examine for possible              tolerance deviations.

5.Stainless steel anchor is available .




PART NUMBER SYSTEM CODE LENGTH (L) SWL TENSION (TON) BODY DIAMETER (B) BASE DIAMETER (C) HEAD DIAMETER (D) HEAD RECESS (F)
1.3-Ton
ULA01.3055 1.3 55 0.97 10 25 19 10
ULA01.3065 1.3 65 1.30 10 25 19 10
ULA01.3085 1.3 85 1.30 10 25 19 10
ULA01.3120 1.3 119 1.30 10 25 19 10
ULA01.3200 1.3 203 1.30 10 25 19 10
2.5-Ton
ULA02.5055 2.5 55 1.06 14 35 26 11
ULA02.5070 2.5 70 2.0 14 35 26 11
ULA02.5085 2.5 85 2.24 14 35 26 11
ULA02.5120 2.5 119 2.50 14 35 26 11
ULA02.5140 2.5 140 2.50 14 35 26 11
ULA02.5170 2.5 170 2.50 14 35 26 11
ULA02.5280 2.5 279 2.50 14 35 26 11
5-Ton
ULA05075 5 76 2.3 20 50 36 15
ULA05095 5 95 2.95 20 50 36 15
ULA05110 5 110 4.0 20 50 36 15
ULA05120 5 119 4.44 20 50 36 15
ULA05140 5 140 5 20 50 36 15
ULA05160 5 160 5 20 50 36 15
ULA05180 5 179 5 20 50 36 15
ULA05240 5 240 5 20 50 36 15
ULA05340 5 340 5 20 50 36 15
7.5-Ton
ULA07.5120 7.5 120 4.40 24 60 47 15
ULA07.5165 7.5 165 7.5 24 60 47 15
ULA07.5300 7.5 300 7.5 24 60 47 15
ULA07.5540 7.5 540 7.5 24 60 47 15
ULA07.5600 7.5 600 7.5 24 60 47 15
ULA07.5680 7.5 680 7.5 24 60 47 15
    10-Ton  
ULA10120 10 119 4.40 28 70 47 15
UL010135 10 135 6.41 28 70 47 15
ULA10150 10 150 7.61 28 70 47 15
ULA10170 10 170 8.35 28 70 47 15
ULA10220 10 225 10 28 70 47 15
ULA10250 10 250 10 28 70 47 15
ULA10340 10 340 10 28 70 47 15
  15-Ton  
ULA15200 15 200 15 34 85 69 15
ULA15400 15 400 15 34 85 69 15
20-Ton
ULA20250 20 250 20 38 98 70 16
ULA20500 20 500 20 38 98 70 16

Allowable SWL based on 2.5:1 safety factor in 15 N/mm2 normal weight concrete.

 
EYE ANCHORS

Eye anchor with Rebar are used in conjunction with the rebar reinforcing bars.

The bars are installed through the eye of the anchor to develop deep tensile action.

This combination allows anchors to develop great safe work loads when used in thin wall section .


PART NUMBER TENSION SYSTEM CODE ANCHOR LENGTH (L) BODY 
DIAMETER (B)
HEAD 
DIAMETER
(D)
HEAD 
RECESS
(F)
HOLE 
LOCATION
(G)
HOLE 
DIAMETER
(H)
SWL (TON)
1-Ton
UEA1.3065 1.3 65 10 20 10 54 10 1
2-Ton
UEA2.5090 2.5 92 14 27 11 76 13 2
4-Ton
UEA5.090 5 92 20 37 16 68 20 4
UEA5.0120 5 121 20 37 16 98 20 4
8-Ton
UEA10115 10 111 29 48 16 87 25 8
UEA10180 10 179 29 48 16 152 25 8
16-Ton
UEA20250 20 250 38 70 16 203 37 16

Allowable SWL based on 3:1 safety factor in 15 N/mm2 normal weight concrete.

 

Note: Headed Eye Anchors require use of bent rebar V through hole to develop tension capacity.

TENSION VEES
ANCHOR PART NO. REQUIRED REBAR SIZE (R) BENT REBAR LEG (P)
UEA1.3065 8 254
UEA2.5090 10 330
UEA5090 16 406
UEA5120 16 406
UEA10115 22 508
UEA10180 22 508
UEA20250 32 838
 

STEEL RECESS FORMERS
This steel body is turned from solid material to locating Pipe double Anchors in steel forms.


PART NUMBER SYSTEM CODE RECESS DIAMETER (D) RECESS HEIGHT (L) HOLE DIAMETER (H) THREAD SIZE
SRF01 1.3 60 29 21 M8
SRF01 2.5 73 33 29 M12
SRF05 5 94 41 38 M12
SRF10 10 121 54 48 M12
Height (L) Diameter (D)
RR01 Rubber Ring Seal 11 21
RR02 Rubber Ring Seal  13 30
RR05 Rubber Ring Seal  14 38
RR10 Rubber Ring Seal  20 49
 

RUBBER RECESS FORMERS

Used to Recess DR Anchors relative to the concrete surface. Each Rubber Recess Former requires one Wing Nut, Plate, and Stud Set to attach it to the form.


PART NUMBER SYSTEM CODE RECESS DIAMETER (D) RECESS HEIGHT (L) HOLE DIA. (H)
RRF01 1.3 59 30 10
RRF02 2.5 73 37 14
RRF04 5 94 48 20
RRF08 10 117 59 29
RRF16 20 162 59 38
 
ARTICULATED STEEL RECESS FORMER
Drilled and tapped to allow bolting directly to the form.
Can be welded to certain types of forms where location is permanent.
 
PART NUMBER SYSTEM CODE
SRF01A 1.3T
SRF02A 2.5T
SRF05A
5.0T


 

WING NUT, PLATE & STUD SETS

Used to hold the Rubber Recess Formers to the formwork.


PART NUMBER SYSTEM CODE STUD DIA. (D) STUD LENGTH (L)
WNP01A 1.3 M8 100
WNP02A 2.5 M12 100
WNP04A 5 M12 100
WNP08A 10 M12 100
WNP16A 20 M16 100
 

UNI LIFTING ANCHOR THREADED PLATES 

Can be used with stud or bolt recess former to form.


PART NUMBER SYSTEM CODE THREADS
ULATP01 1.3 M8
ULATP02 2.5 M12
ULATP04 5 M12
ULATP08 10 M12